Re: [PATCH 09/10] arm64: dts: qcom: Add PMR735d pmic dtsi

[Konrad Dybcio]

On 16/11/2022 11:31, Abel Vesa wrote:
> From: Neil Armstrong <neil.armstrong@xxxxxxxxxx>
>
> Add nodes for PMR735d in separate dtsi file.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@xxxxxxxxxx>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>

Konrad
>   arch/arm64/boot/dts/qcom/pmr735d.dtsi | 104 ++++++++++++++++++++++++++
>   1 file changed, 104 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/qcom/pmr735d.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/pmr735d.dtsi b/arch/arm64/boot/dts/qcom/pmr735d.dtsi
> new file mode 100644
> index 000000000000..41fb664a10b3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/pmr735d.dtsi
> @@ -0,0 +1,104 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2022, Linaro Limited
> + */
> +
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +/ {
> +	thermal-zones {
> +		pmr735d-k-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <0>;
> +
> +			thermal-sensors = <&pmr735d_k_temp_alarm>;
> +
> +			trips {
> +				trip0 {
> +					temperature = <95000>;
> +					hysteresis = <0>;
> +					type = "passive";
> +				};
> +
> +				trip1 {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "hot";
> +				};
> +			};
> +		};
> +
> +		pmr735d-l-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <0>;
> +
> +			thermal-sensors = <&pmr735d_l_temp_alarm>;
> +
> +			trips {
> +				trip0 {
> +					temperature = <95000>;
> +					hysteresis = <0>;
> +					type = "passive";
> +				};
> +
> +				trip1 {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "hot";
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +
> +&spmi_bus {
> +	pmr735d_k: pmic@a {
> +		compatible = "qcom,pmr735d", "qcom,spmi-pmic";
> +		reg = <0xa SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pmr735d_k_temp_alarm: temp-alarm@a00 {
> +			compatible = "qcom,spmi-temp-alarm";
> +			reg = <0xa00>;
> +			interrupts = <0xa 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> +			#thermal-sensor-cells = <0>;
> +		};
> +
> +		pmr735d_k_gpios: gpio@8800 {
> +			compatible = "qcom,pmr735d-gpio", "qcom,spmi-gpio";
> +			reg = <0x8800>;
> +			gpio-controller;
> +			gpio-ranges = <&pmr735d_k_gpios 0 0 2>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +
> +	pmr735d_l: pmic@b {
> +		compatible = "qcom,pmr735d", "qcom,spmi-pmic";
> +		reg = <0xb SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pmr735d_l_temp_alarm: temp-alarm@a00 {
> +			compatible = "qcom,spmi-temp-alarm";
> +			reg = <0xa00>;
> +			interrupts = <0xb 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> +			#thermal-sensor-cells = <0>;
> +		};
> +
> +		pmr735d_l_gpios: gpio@8800 {
> +			compatible = "qcom,pmr735d-gpio", "qcom,spmi-gpio";
> +			reg = <0x8800>;
> +			gpio-controller;
> +			gpio-ranges = <&pmr735d_l_gpios 0 0 2>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +};