Re: [PATCH 1/2] dt-bindings: PCI: qcom: Add SM8550 to binding

[Johan Hovold]

On Wed, Nov 16, 2022 at 02:35:04PM +0200, Abel Vesa wrote:
> Add the SM8550 platform to the binding.
> 
> Signed-off-by: Abel Vesa <abel.vesa@xxxxxxxxxx>
> ---
>  .../devicetree/bindings/pci/qcom,pcie.yaml    | 96 +++++++++++++++++++
>  1 file changed, 96 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie.yaml
> index 54f07852d279..efa01a8411c4 100644
> --- a/Documentation/devicetree/bindings/pci/qcom,pcie.yaml
> +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.yaml
> @@ -34,6 +34,8 @@ properties:
>        - qcom,pcie-sm8250
>        - qcom,pcie-sm8450-pcie0
>        - qcom,pcie-sm8450-pcie1
> +      - qcom,pcie-sm8550-pcie0
> +      - qcom,pcie-sm8550-pcie1

You should only need one compatible even if there are differences in
which bus clocks you need to enable.

>        - qcom,pcie-ipq6018
>  
>    reg:
> @@ -92,6 +94,10 @@ properties:
>    power-domains:
>      maxItems: 1
>  
> +  enable-gpios:
> +    description: GPIO controlled connection to ENABLE# signal
> +    maxItems: 1
> +
>    perst-gpios:
>      description: GPIO controlled connection to PERST# signal
>      maxItems: 1
> @@ -187,6 +193,8 @@ allOf:
>                - qcom,pcie-sm8250
>                - qcom,pcie-sm8450-pcie0
>                - qcom,pcie-sm8450-pcie1
> +              - qcom,pcie-sm8550-pcie0
> +              - qcom,pcie-sm8550-pcie1
>      then:
>        properties:
>          reg:
> @@ -601,6 +609,92 @@ allOf:
>            items:
>              - const: pci # PCIe core reset
>  
> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            enum:
> +              - qcom,pcie-sm8550-pcie0
> +    then:
> +      properties:
> +        clocks:
> +          minItems: 11
> +          maxItems: 11
> +        clock-names:
> +          items:
> +            - const: pipe # PIPE clock
> +            - const: pipe_mux # PIPE MUX
> +            - const: phy_pipe # PIPE output clock

The mux and pipe output does not belong in the binding and instead the
muxing should be handled by the clock driver (cf. sc8280xp). You can
probably drop the refclock too.

> +            - const: ref # REFERENCE clock
> +            - const: aux # Auxiliary clock
> +            - const: cfg # Configuration clock
> +            - const: bus_master # Master AXI clock
> +            - const: bus_slave # Slave AXI clock
> +            - const: slave_q2a # Slave Q2A clock
> +            - const: ddrss_sf_tbu # PCIe SF TBU clock
> +            - const: aggre0 # Aggre NoC PCIe0 AXI clock

Johan