Re: [PATCH 1/1] mmc: sdhci: Fixed too many logs being printed during tuning

[Wenchao Chen]

On Fri, Nov 18, 2022 at 11:57 PM Adrian Hunter <adrian.hunter@xxxxxxxxx> wrote:
>
> On 18/11/22 11:25, Wenchao Chen wrote:
> > On Thu, Nov 17, 2022 at 12:00 AM Adrian Hunter <adrian.hunter@xxxxxxxxx> wrote:
> >>
> >> On 11/11/22 10:42, Wenchao Chen wrote:
> >>> From: Wenchao Chen <wenchao.chen@xxxxxxxxxx>
> >>>
> >>> During the HS200 tuning process, too many tuning errors are printed in
> >>> the log.
> >>>
> >>> Signed-off-by: Wenchao Chen <wenchao.chen@xxxxxxxxxx>
> >>> ---
> >>>  drivers/mmc/host/sdhci.c | 4 ++++
> >>>  1 file changed, 4 insertions(+)
> >>>
> >>> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
> >>> index fef03de85b99..a503b54305eb 100644
> >>> --- a/drivers/mmc/host/sdhci.c
> >>> +++ b/drivers/mmc/host/sdhci.c
> >>> @@ -3401,6 +3401,10 @@ static void sdhci_data_irq(struct sdhci_host *host, u32 intmask)
> >>>               if (host->pending_reset)
> >>>                       return;
> >>>
> >>> +             command = SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND));
> >>> +             if (command == MMC_SEND_TUNING_BLOCK || command == MMC_SEND_TUNING_BLOCK_HS200)
> >>> +                     return;
> >>
> >> Normally we wouldn't get here even if a request got an error because
> >> then we either reset the data circuit which should stop further
> >> interrupts, or set host->pending_reset.
> >>
> >> Can you elaborate on what is going wrong?
> >>
> > Hi  adrian
> > 1. In the process of tuning, not all tuning values are good, some
> > tuning values may cause errors, and these errors print too many logs.
> >     Of course, we reset the cmdline or dataline on error.
> > 2. use host->pending_reset = true
> > static void __sdhci_finish_mrq(struct sdhci_host *host, struct mmc_request *mrq)
> > {
> > ...
> > if (sdhci_needs_reset(host, mrq))
> > host->pending_reset = true;
> > ...
> > }
> >
> > But intmask = 0x00200000
> > static void sdhci_data_irq(struct sdhci_host *host, u32 intmask)
> > {
> > ...
> > if (!host->data) {
> > struct mmc_command *data_cmd = host->data_cmd;
> >
> > if (data_cmd && (data_cmd->flags & MMC_RSP_BUSY)) {
> > if (intmask & SDHCI_INT_DATA_TIMEOUT) { //#define
> > SDHCI_INT_DATA_TIMEOUT 0x00100000
> > host->data_cmd = NULL;
> > data_cmd->error = -ETIMEDOUT;
> > sdhci_err_stats_inc(host, CMD_TIMEOUT);
> > __sdhci_finish_mrq(host, data_cmd->mrq);//<=
> > return;
> > }
> > if (intmask & SDHCI_INT_DATA_END) {    //#define  SDHCI_INT_DATA_END 0x00000002
> >
> > host->data_cmd = NULL;
> > /*
> > * Some cards handle busy-end interrupt
> > * before the command completed, so make
> > * sure we do things in the proper order.
> > */
> > if (host->cmd == data_cmd)
> > return;
> >
> > __sdhci_finish_mrq(host, data_cmd->mrq);//<=
> > return;
> > }
> > }
> > ...
> > if (host->pending_reset)
> > return;
> >
> > pr_err("%s: Got data interrupt 0x%08x even though no data operation
> > was in progress.\n",
> >        mmc_hostname(host->mmc), (unsigned)intmask);
> > sdhci_err_stats_inc(host, UNEXPECTED_IRQ);
> > sdhci_dumpregs(host);
> >
> > return;
> > }
> > ...
> > }
>
> Not really following that I'm sorry.
>
> Are you saying you get a data interrupt after he data circuit is reset?
>

No. During the tuning process, sdhci_data_irq does not skip printing
because the interrupt state is 0x00200000 (DATA CRC ERROR).

> >
> >>> +
> >>>               pr_err("%s: Got data interrupt 0x%08x even though no data operation was in progress.\n",
> >>>                      mmc_hostname(host->mmc), (unsigned)intmask);
> >>>               sdhci_err_stats_inc(host, UNEXPECTED_IRQ);
> >>
>