Re: [PATCH 1/2] arm64: dts: qcom: sm8550: Add UFS host controller and phy nodes

[Konrad Dybcio]

On 16/11/2022 13:51, Abel Vesa wrote:
> Add UFS host controller and PHY nodes.
>
> Signed-off-by: Abel Vesa <abel.vesa@xxxxxxxxxx>
> ---
>   arch/arm64/boot/dts/qcom/sm8550.dtsi | 76 ++++++++++++++++++++++++++++
>   1 file changed, 76 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
> index 07ba709ca35f..27ce382cb594 100644
> --- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
> @@ -1372,6 +1372,82 @@ mmss_noc: interconnect@1780000 {
>   			qcom,bcm-voters = <&apps_bcm_voter>;
>   		};
>   
> +		ufs_mem_phy: phy@1d80000 {
> +			compatible = "qcom,sm8550-qmp-ufs-phy";
> +			reg = <0x0 0x01d80000 0x0 0x200>;

> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
These three can go at the bottom.


> +			clock-names = "ref", "qref";
> +			clocks = <&gcc GCC_UFS_PHY_PHY_AUX_CLK>,
> +				 <&tcsr TCSR_UFS_CLKREF_EN>;
> +
> +			power-domains = <&gcc UFS_MEM_PHY_GDSC>;
> +
> +			resets = <&ufs_mem_hc 0>;
> +			reset-names = "ufsphy";
> +			status = "disabled";
> +
> +			ufs_mem_phy_lanes: phy@1d80400 {
> +				reg = <0x0 0x01d81000 0x0 0x134>,
> +				      <0x0 0x01d81200 0x0 0x3d8>,
> +				      <0x0 0x01d80400 0x0 0x258>,
> +				      <0x0 0x01d81800 0x0 0x134>,
> +				      <0x0 0x01d81a00 0x0 0x3d8>;
> +				#phy-cells = <0>;
> +			};
> +		};
> +
> +		ufs_mem_hc: ufshc@1d84000 {
> +			compatible = "qcom,sm8550-ufshc", "qcom,ufshc",
> +				     "jedec,ufs-2.0";
> +			reg = <0x0 0x01d84000 0x0 0x3000>;
> +			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
> +			phys = <&ufs_mem_phy_lanes>;
> +			phy-names = "ufsphy";
> +			lanes-per-direction = <2>;
> +			#reset-cells = <1>;
> +			resets = <&gcc GCC_UFS_PHY_BCR>;
> +			reset-names = "rst";
> +
> +			power-domains = <&gcc UFS_PHY_GDSC>;
> +
> +			iommus = <&apps_smmu 0x60 0x0>;
> +
> +			interconnects = <&aggre1_noc MASTER_UFS_MEM 0 &mc_virt SLAVE_EBI1 0>,
> +					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_UFS_MEM_CFG 0>;
> +
> +			interconnect-names = "ufs-ddr", "cpu-ufs";
> +			clock-names =
Why break the line before adding any entries?

Konrad
> +				"core_clk",
> +				"bus_aggr_clk",
> +				"iface_clk",
> +				"core_clk_unipro",
> +				"ref_clk",
> +				"tx_lane0_sync_clk",
> +				"rx_lane0_sync_clk",
> +				"rx_lane1_sync_clk";
> +			clocks =
> +				<&gcc GCC_UFS_PHY_AXI_CLK>,
> +				<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
> +				<&gcc GCC_UFS_PHY_AHB_CLK>,
> +				<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
> +				<&rpmhcc RPMH_LN_BB_CLK3>,
> +				<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
> +				<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
> +				<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
> +			freq-table-hz =
> +				<75000000 300000000>,
> +				<0 0>,
> +				<0 0>,
> +				<75000000 300000000>,
> +				<100000000 403000000>,
> +				<0 0>,
> +				<0 0>,
> +				<0 0>;
> +			status = "disabled";
> +		};
> +
>   		tcsr_mutex: hwlock@1f40000 {
>   			compatible = "qcom,tcsr-mutex";
>   			reg = <0x0 0x01f40000 0x0 0x20000>;